Sunday 27 December 2015

Tutorial: Malifaux Basing

Malifaux Basing Tutorial

As you may know I am slowly building up a Malifaux Resurrectionist crew based around undead Samurai. Looking around I could not find any basing tutorials to create my own, as I did not want to go down the expensive resin route. Well after a bit of experimentation I created my own bases, and have done a tutorial below on how I made them. The theme is a rotting dojo or building, with planks and moss etc, simple but effective :)

Materials

First you will need to gather all the kit and materials you need for the job. It is better to have them to hand otherwise you will find the glue dries etc before you can start another stage.

  • Strips of Balsa wood (about 3mm thick)
  • Sand mix (my own creation, using builders sand and a little grit. Normal sand will work just fine as well, this just adds a little more texture)
  • Superglue (this needs to be runny. I buy really cheap glue from the pound shop which is exceptionally runny, and works a dream for the basing. The more thicker stuff may work ok but you want it to be easy flowing if possible)
  • Scalpel
  • Grass tufts (I use army painter tufts, but static grass will work fine. I just prefer the longer strands of grass)

Step 1

Cut your balsa wood into thin strips. Make sure the cuts are wonky, as this will give the wood a worn look and add more variation to the bases later.


Step 2


Grab your scalpel and start carving into the sides of the balsa strip to add more texture and indents to it.

Keep the shavings in a small pile to the side once you are done as you will need them later.








Step 3

 

Tear the balsa strips into small chunks. Don't cut these with the knife as you want the edges to be jagged and splintered.

 

 

Step 4

 

Position the chunks of wood onto the base until you are happy with the look of it.

Don't be afraid to tear and break the strips apart into smaller ones if you need. This just adds more texture.

Use the shavings to fill any gaps.

Use superglue to bind them together and wait for it to dry.

 

 

Step 5

 

Squirt a load of superglue into the recesses of the planks

 

 

Dip it into your sand mix as quick as you can.

 

 

 

 

 

 

The superglue will naturally form nice clumps and set very quickly. You can't really get this effect with other glues as the drying times are too long. This method is quick and very effective.

 

 

 

 

Step 6

 

Your base is now ready for priming and painting. Here I sprayed it black and then drybrushed up from a dark brown, mixing in ushabti bone for the final brown highlight.

The green is again drybrushed, but only in selected places, to simulate moss & rotting boards.

Finally I paint the rim black before adding the mini on top.

 

 

 

Once the mini and base are assembled together I gloss varnish, then do a dullcoat on top to matt it back down again. You don't need to do this step, bit I like to protect my mini from the rigours of gaming, and the two varnishing steps give a slight satin finish that I am quite fond of, as I think it adds more of a depth to the colours.

When the varnishing is complete I finally add a few select tufts of the grass into recesses in the boards for the final effect.

 

 

 

The final result

 

I hope you have enjoyed this and found it useful. Let me know in the comments if so :)

NafNaf

 

11 comments:

  1. That looks amazing. Great job on the tutorial as well.

    ReplyDelete
    Replies
    1. Thanks dude. I enjoyed writing it, and am planning a few more in the future I hope :)

      Delete
  2. Fantastic tutorial, creating your own worn wood strips looks awesome.

    ReplyDelete
  3. Great tutorial! Look amazing! Might just try this out for my new daemons ;)

    ReplyDelete
    Replies
    1. Thanks very much :)

      Def give it a go, it is actually really
      Fun to do, and painting them is dead easy, just lots of drybrushing

      Delete
  4. Welcome to the Wyrd side ... oooooh, scary. I have been waiting to use that one forever! Great tutorial. I did something similar for my Gremlin's swamp bases.
    Another trick I found is put down some PVA and put drops of superglue on it. The superglue reacts with the PVA to make this funky snot/water looking stuff.

    ReplyDelete
    Replies
    1. Lol :D Thanks Adam.

      Nice tip! I will def have to try that out on a few tester bases. I find basing really fun (I know, wryd right ;) ) so trying/finding out new techniques is great as I get to play :)

      Delete
    2. Ha! Wyrd. You crack me up. It's nice to find someone else who "gets it" about basing as much as I do.

      Delete
    3. Also, I fond a photo of the result:
      http://www.spruegrey.com/killjoy/
      to give you an idea of what happens. Sorta.

      Delete
    4. Oh cool, that is a very interesting effect. Thanks for the link :)

      Delete